D80_5
D80_4D80_3D80_2D80_1

d&b audiotechnik D80

The 2 RU four channel D80 amplifier is a high power density amplifier, ideally suited for use in both mobile and installation environments. It contains configurations for all d&b loudspeakers and a linear mode. The signal delay capability enables user definable settings of up to 10 s (= 3440 m/11286 ft) to be applied independently to each channel. The same applies to the two 16-band equalizers, providing optional parametric, asymmetric, shelving or notch filtering.

The D80 incorporates a colour TFT touchscreen, offering quick access to the menu structure, while the rotary encoder can be used for fine adjustment. The front panel and the integrated touchscreen of the D80 amplifier is tilted up for ease of operation when the amplifier is below eye level.

The equal ratio of signal input to amplifier output channels increases the application flexibility particularly for monitor, frontfill or effect channel use.

The LoadMatch function integrated within the D80 amplifier enables the electrical compensation of loudspeaker cable properties, without the need for an extra conductor. This results in an increased accuracy of audio reproduction over a bandwidth of up to 20 kHz, preserving the tonal balance when cable lengths of up to 70 m (230 ft) are used. The D80 incorporates Class D amplifiers utilizing a power supply with active Power Factor Correction (PFC) suitable for mains voltages 100 V/120 V/200 V/230 V, 50 – 60 Hz and maintains a stable output when used with weak or unstable mains supplies. An NL8 provides all outputs on a single connector, while individual outputs are optionally NL4 or EP5 connectors. RJ 45 and etherCON connectors enable access to the d&b Remote network via CAN-Bus and OCA via Ethernet respectively.

  • Control and indicators
  • POWER Mains power switch
  • SCROLL/EDIT Digital rotary encoder
  • Display Colour TFT touchscreen, 35″/320 x 240 pixel
  • Digital Signal Processing
  • Equalizer 2 x 16-band PEQ/notch/shelving/asymmetric
  • Latency analog and digital inputs 0,3 msec Delay setting 0,3 – 10000 msec Configurations current d&b loudspeakers and linear mode
  • Function switches d&b loudspeaker specific circuits
  • Frequency generator Pink noise or Sine wave Sampling rate96 kHz/27 Bit ADC/24 Bit DAC
  • Connectors
  • INPUT ANALOG (A1 – A4) 3 pin XLR female
  • ANALOG LINK (A1 – A4) 3 pin XLR male
  • INPUT DIGITAL (D1/2, D3/4) 3 pin XLR female AES 3
  • DIGITAL LINK (Output) 3 pin XLR male
  • Sampling Digital AES/EBU 48 kHz/96 kHz
  • SPEAKER OUTPUTS A/B/C/D NL4, optional EP5 4
  • CHANNEL OUTPUT NL8
  • CAN 2 x RJ 45 parallel
  • ETHERNET 2 x etherCON1, 10/100 Mbit Ethernet
  • Mains connector powerCON-HC1
  • Data (linear setting with subsonic filter)
  • Maximum output power per channel (THD + N < 05 %, all channels driven)
  • CF = 6 dB at 4/8 ohms4 x 2600/2000 W
  • CF = 12 dB at 4/8 ohms4 x 4000/2000 W
  • S/N ratio (unweighted, RMS)
  • Analog input > 110 dBr
  • Digital input > 114 dBr
  • Power supply
  • Autosensing switch mode power supply with active Power Factor Correction (PFC) Rated mains voltage
  • High range 208 – 240 V, 50 – 60 Hz
  • Low range 100 – 127 V, 50 – 60 Hz
  • Dimensions, weight
  • Height x width x depth 2 RU x 19” x 5305 mm/209″
  • Weight 19 kg/42 lb
Varenummer: Z2710.001. Kategorier: , .

Produktbeskrivelse